Wednesday, December 5

SLASHED: The L-Rider Transformer $68.95



..its Discountvapers











Telescoping Transformer VV Mod - Chrome (Body Only)

Adjust Vaping Air Flow, Check atomizer Resistance, change voltages and use a variety of batteries!  This unit does it all. 

The Telescoping Transformer accepts All 510 and eGo threaded atomizers, clearomizers, cartomizers, vivi nova tanks, Map Tanks, J-Tanks, CE4, CE5 and all ohm ratings from 1.0ohm to 5.0ohms. With the Telescoping Transformer VV Mod you can use a variety of different size batteries from 18350, 18500 to 18650 Protected or Unprotected

The Telescoping Transformer VV Mod is packed with Features:
Aluminum body


  • power button
  • voltage up button
  • voltage down button
  • activation button
  • LCD screen, which shows the current voltage the device is set on.
  • 510 threaded and Joye Ego Atomizer compatible *NEW*!
  • vented removable end cap w/ spring for battery tension
Tech Specs:
Selectable voltage from 3.0V~6.0V in 0.1V increments

Telescoping Transformer VV Mod Body Unit Dimensions: 5.15"L x 0.86"D
Features:

Air flow controller, just spin the top for more or les airflow!:
The top of the unit has a free spinning ring that opens or closes 5 air holes allowing you to control how much air goes to your cartomizer

Side Power Button:
This button makes it much easier to hold and fire your PV and will not get stuck in the on position like other PV's, it also prevents desk roll around :) 

Resistance Check *NEW*:
Push the large activation button 5 times and the LCD will display the resistance of the attached atomizer or cartomizer.
Low Resistance Atomizers *NEW*:
The Telescoping Transformer VV Mod will work with atomizer of 1.0 ohm or higher.
Ego Compatible *NEW*:
The Telescoping Transformer VV Mod is compatible with Joye Ego Series Atomizers without the use of an adapter. Ego CE4 Plus will also fit.
Spring Loaded Center Post *NEW*:
Shake the unit and it may rattle. Don't be alarmed. This faint noise is due to the newly designed spring loaded center post (seen here). This new center post will preventing "post-pulling" and other related contact issues.
Power on/Off Button: 
hold the button down for 5 seconds to turn the device on, hold the button again for 5 seconds to turn the device off.
+ Button: On press, increases voltage by 0.1V increments between 3.0V~6.0V.- Button: On press, decreases voltage by 0.1V increments between 3.0V~6.0V.+ and – Button: Press and hold both buttons for five second to disable the + and – button, locking the device on the voltage it is currently set at.Regulated output:
Keeps the voltage the same with each puff regardless of the remaining battery power. As the battery drains, the device will keep the voltage consistent.
10 Second Cutoff timer:
If the activation button is held down for 10 seconds or longer, the Telescoping Transformer VV Mod will shut itself off until the button is released. To prevent overheating the atomizer and the device.
Short Circuit/Atomizer Protection:
The Telescoping Transformer VV Mod can recognize an atomizer with too low of a resistance for the current voltage setting and will drop the voltage to 3.7V to protect both the battery and atomizer. If the atomizer is too low or shorted out it will shut off power to the device to protect the Telescoping Transformer VV Mod from being damaged.
Reverse Battery Protection: 
Protects the device in case you put the battery in the device backwards
Battery Monitoring/Over-Discharge Protection:
The device will monitor the battery voltage and automatically turn off when the battery is discharged, preventing damage to the battery by overly depleting it.
Battery Voltage Meter:
The Telescoping Transformer VV Mod has a voltage meter built in, simply press the red power button 6 times and it will display the voltage of the battery for a few seconds. This way you can monitor the power left in the battery before it needs to be recharged. 18650 batteries provide 4.2V at peak charge and over the life of the battery that voltage will decrease to about 3.3V level before needing to be recharged.  This will help you monitor the life cycle of the battery. The LCD screen will flash when the battery needs to be recharged, and will stop powering the device.
Amperage Limiting to 2.5 amps: 
The device should monitor and shut itself off if it detects any excessive over-current conditions.

Vent hole on the bottom of the device for added safety


WHERE:  http://www.discountvapers.com/

$68.95